History

9100C ANESTHESIA MACHINE PDF

GE Healthcare c Anesthesia Machine Technical Reference Manual Software Revision 1.x Approved −12−9 EET Junmin Ji (Rick) M c Product Data Sheet – GE Healthcare c Familiar, reliable, GE – with over years experience in anesthesia and quality leadership? 53 cm/21 in Depth: 40 cm/16 in Side of machine: cm/45 in Height: The c is the ideal solution for customers seeking an affordable, reliable and easy-to-use anaesthesia system. The c is designed and manufactured in.

Author: Kajigal Nikogar
Country: Sierra Leone
Language: English (Spanish)
Genre: Life
Published (Last): 21 November 2008
Pages: 263
PDF File Size: 14.47 Mb
ePub File Size: 12.69 Mb
ISBN: 608-8-19266-755-3
Downloads: 31749
Price: Free* [*Free Regsitration Required]
Uploader: Sagore

Multipurpose Anaesthesia Machine- 9100C

Call Send a quick message. The interlock system prevents purging more than one vaporizer at a time. The bellows should fill in approximately 3. Gas supply Pipeline input range: Put your hand on the inlet of the leak-test device. Low flow, low vacuum Low flow, low vacuum Low flow, low vacuum Robust and reliable, the c is compact and lightweight, easy to manoeuver in any Insert the tubing into the fitting until the ferrule seats in the fitting.

In the Standby position The switch turns off the ventilator electrical. Get best deals for coconut. Engine The pneumatic Vent Engine consists of the hardware that drives the ventilator bellows.

Connect the fresh gas and flush gas tubing.

After all regulators have been tested, perform the Post-service checkout Section 3. If test fails, tighten, repair, or replace as needed. Remove the plug on the test fitting, and attach pressure test device to the test fitting. If the indicator is not on, the display assembly is not aneshesia AC power.

It is piloted closed during inspiration and remains closed until the bellows is refilled during exhalation. Reinstall the breathing system.

Remove the nut and washer that hold the encoder to the keyboard. Test the anesthesia machine for low-pressure leaks: Record the new web site generated Key Machhine on a sticker.

Verify that the output of the tested regulator is within the range listed in the chart. The assemblies should snap into place.

Loosen the two screws A. Carefully inspect the circuit module for damaged seals or misassembly, and the seating of the O2 sensor if equipped. Note This replacement and test procedure is a service action and is not part of the maintenance program.

Connect the calibration fitting See Section From the Service Mode, perform the following: Loosen the screws C that hold the two enclosures together one in each corner. Remarks If any of the select buttons test fails, replace the front panel keyboard mavhine.

Inspect the new flapper B and valve seat for nicks, debris and cleaniness. Push the adapter into the ACGO outlet throughout the test to get a good nachine. Open the cylinder yokes. Pull the anestheeia out of the valve body.

Mains supply inlet 7.

Check cable connection; replace cable. A digital clinical decision support tool that puts relevant, reliable, and predictive information at your fingertips. Disconnect pipeline supplies; close cylinder valves; bleed off Vent Engine pressure Section 9. Bellows mounting rim loose Remove rim and pop-off valve diaphragm; reseat diaphragm; snap rim into place. CAUTION Servicing of this product in accordance with this Technical Reference manual should never be undertaken in the absence of proper tools, test equipment and the most recent revision to this service manual which is clearly and thoroughly understood.

The following illustration shows the parts. Transfer harness wire to top and middle tabs; bottom tab open. Remarks Ensure the flow sensor is correctly connected as detailed in the calibration setup. When engaged, the O2 and N2O knobs turn together: Turn all flow controls fully clockwise closed. Make sure tubing connections are tight. Follow the menu structure outlined below to reach the adjustment for the inspiratory flow valve.

N2O flow does not decrease Defective flowmeter assembly Verify low pressure regulator calibration. Comments and suggestions on this manual are invited from our customers.

Multipurpose Anaesthesia Machine- C – Yoga Enterprises, Pune | ID:

Place the new APL valve into position with the setting indicator facing to Front the front of the machine. Set the system switch to Standby when regulator is adjusted.

Two screws from each side madhine. Adjust O2 flow to 0. The test device gauge should read within the values indicated. Warnings and Cautions tell you about dangerous conditions that can occur if you do not follow all instructions in this manual: