Finance

ASTM A860 PDF

ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.

Author: Arasida Yozshuhn
Country: South Africa
Language: English (Spanish)
Genre: Technology
Published (Last): 11 February 2004
Pages: 158
PDF File Size: 1.17 Mb
ePub File Size: 13.6 Mb
ISBN: 899-1-65634-802-6
Downloads: 24976
Price: Free* [*Free Regsitration Required]
Uploader: Nikoll

BoxArlingate Ln. Wrought austenitic and austenitic-ferritic duplex stainless steels without specific inspection requirements BS EN Butt-welding pipe fittings Part 4: Width of specimen 11?

NDE personal shall be. Specimens shall conform to required values of chemical composition and mechanical properties, namely: The nickel content of the deposited weld metal shall not exceed 1.

Research use only,Commercial use is prohibited.

Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment.

JIS G Carbon steel pipes for pressure service. Workmanship, Finish and Appearance This abstract is a brief summary of the referenced standard. Weld-metal specimens shall be specimens with the axis transverse to the weld seam. Standard Specimen, Size Specimen. In addition, if requested to provide test reports, the manufacturer shall also provide the following, when applicable: No cracks shall be permitted.

A860 WPHY 60 PIPE FITTTINGS

When the section astmm lies between two values de? Asstm to Active This link will always route to the current Active version of the standard. Committee A01 has identi? All butt — weld tees manufactured by cold —forming methods shall be liquid.

The impact specimens shall not be? Materials and Manufacture 5. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Only the side wall area of the tees need be examined. The chemical composition thus determined.

NDE personnel shall be quali?

ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.

Section V, Nondestructive Examination. Current edition approved Nov. Rejection and Rehearing Rectangular For Less than [7. There sults shall conform to Table 1 for either.

This area is de? These fittings are for use in high-pressure gas and oil transmission and distribution systems. The wall thickness at all points shall be at least ? The requirements are not intended to give assurance against fracture propagation.

DIN Medium-weight threaded steel tubes. Within the asm, the SI units are shown in brackets. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Repair by Welding Base Metal Internal and external surfaces shall be examined when size permits accessibility.

A860 WPHY 65 PIPE FITTTINGS

One or more of the supplementary requirements may be speci? Cvenergy absorptionC; measured at? Other imperfections shall be treated in accordance with These fittings are for use in. Materials and Manufacture … Research use only,Commercial use is prohibited. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. After the removal of any cracks, the tees shall be re-examined by the original method.

By Sea or By Land Packing: Combining values from the two systems may result in non-conformance with the standard. The chemical composition shall conform to Table 1. Full size Charpy, V-notch specimens q860 be used whenever possible. How can I help you? Within the text, the SI units asm shown in brackets. NOTE 1—For purposes of identi? This specification covers wrought high-strength low-alloy butt-welding steel fittings of seamless and electric fusion-welded construction for applications in high-pressure gas and oil transmission and distribution systems.