ASTM B Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel. Buy ASTM B SPECIFICATION FOR ELECTRODEPOSITED COATINGS OF ZINC ON IRON AND STEEL from SAI Global. ASTM B Type II and III zinc chromate plating Q&A’s. In my opinion a Mil-C- [link is to free spec at Defense Logistics Agency, ] plating.

Author: Gogis Nakora
Country: Rwanda
Language: English (Spanish)
Genre: Environment
Published (Last): 12 June 2015
Pages: 236
PDF File Size: 9.91 Mb
ePub File Size: 9.67 Mb
ISBN: 988-1-42924-270-4
Downloads: 25903
Price: Free* [*Free Regsitration Required]
Uploader: Gozragore

What process variation would produce these different results? Unless a need can be demonstrated, separately prepared specimens shall not be used in place of production items for nondestructive and visual examinations. The values are only relative, since individual studies in various parts of the world have resulted in?

ASTM B-633 Type II vs. III zinc plating

August 31, Asmt. In 24 years I have only been asked this question once before and I presume it involves phosphating over zinc plating for those heavy phosphating grammage applications, where normal phosphating will not provide enough zinc phosphate that is required in the deposit. This standard is subject to revision at any time by the responsible technical committee and must axtm reviewed every? A number in parentheses indicates the year of last reapproval.

Zinc Coating

Sorry, but if you need one particular look, you must go through the ugly process of maintaining sample boards with acceptable vs. Going with clear will make it difficult to tell what is fre chromated zinc vs.

NOTE 1—Surfaces should be activated as soon as possible following baking and handled carefully to avoid contamination and maintain an active surface for post processing. You can get the same finish only for blue and black hex chrome with tri substitutes, but not for yellow or olive as of yet.

The frer data, based on worldwide testing, can be used to compare the behavior of electrodeposited coatings of zinc in various atmospheres. It still will have Hex Chrome. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

From beautiful Pine Beach New Jersey: This guide provides for two plans: The baking treatment shall be ftee before the application of the supplementary treatments and within 4 h of removal from the last process. These separate specimens shall be introduced into a lot at regular intervals before the cleaning operations, preliminary to electroplating, and shall not be separated therefrom until after completion of electroplating.

It is recommended that the following appropriate recommended practices and guides be used: Surfaces to be painted should be ONLY lightly chromated. The coating shall not be stained or discolored.

The chromate, passivate, or supplemental? They b363 be reconsidered for inspection in accordance with Test Method B Electroplated springs and other parts subject to?

I’ve seen this done less commonly on chromated zinc plating than on chromated aluminum. This standard has been approved for use by agencies of the Department of Defense. I have the exact same questions. We are getting poor coverage on the as-cast surface of some steel castings using a yellow Zinc chromate. When Test Methods BBor B b6333 used, remove the supplementary treatment prior to testing. The inspection lot is then classi? Additional types have been added to permit non-chromate passivate treatments to be used in replacement of hexavalent chromium.

Olive green and Black passivation is thick and has high electrical resistance. Perhaps some confusion with Service Condition SC 2 moderatewhich indicates a minimum zinc thickness of 8 microns and is commonly clear chromated Type III.

The Zinc coating provides a smooth look as well as good anti-corrosive protection.

Zinc Plating: ASTM B Type II vs. III

It does not cover electrodeposited zinccoated steel wire or sheets see Speci? Olive Drab chromate is hrs. Decorative charastreistics The exterior visual determined according to last layer. The black layer has also additional target —prevention of light reflection from the part and is used for optical parts. Zinc coating with colorless RoHS compliance passivation.

Ken Vlach – Goleta, California. For these reasons a? Until a very few years ago chromate conversion coatings were based on hexavalent chromium, and deposited a thick film that was relatively easy to dye.

The Zinc coating on the steel does not last shiny for long, and so a freee thick layer coating is added, called passivation. Conditions affecting the electroplating of specimens, including the spacing, plating media, bath agitation, temperature, etc.

Colorful RoHS compliance passivation gives corrosion resistance ability of hours according to ASTM B until white spots-also intended to parts used in a high corrosive environment —outdoor.

According to RoHS the homogeneous and non-homogeneous are defined in such manner that every one may understand that the layer is removable let’s see how.